What it is forTurn the 3D model with the mouse, look at the bite, change how it looks, cut through it, and save a picture or a file for the lab.
What you getYou can show the patient their own teeth in 3D and keep a picture in the patient document.
Where to find itLeft menu → 3D Scans → choose a patient → click a scan
Who can use itOwner and staff with the 3D Scans permission

1Open a scan and turn it

  1. On 3D Scans, choose the patient.
  2. Click a scan in the left list, for example Upper Arch.
  3. Wait for "Opening scan — large files take a moment" to go away.
  4. Drag with the left mouse button to rotate the model.
  5. Scroll the mouse wheel to zoom.
  6. Drag with the right mouse button to move the model sideways.
  7. Click one of the small axis balls to snap to a straight view.

Tip: Lost the model? Click Fit to screen on the tool strip.

Note: If you see "The 3D viewer could not start in this browser", switch on hardware acceleration in the browser and reload the page.

Drawing of the screen. Your own names and numbers will be different.

2Use the tool strip on the model

  1. Look at the dark strip of buttons at the top right of the model.
  2. Click Zoom in, Zoom out or Fit to screen.
  3. Click Reference grid to show or hide a floor grid.
  4. Click Brighter lighting for more light.
  5. Click the Display button to change the look: solid, then wireframe, then xray (see-through), then solid again.
  6. Click Appearance & export to open the colour and export panel under the model.
  7. Click Cross-section to cut through the model, Screenshot to save a picture, or Fullscreen to fill the screen.

Tip: When the look is not solid, a small label on the model tells which look is on.

Note: There is no ruler or measuring tool in the 3D viewer. The "xray" look only makes the model see-through; it is not an X-ray image.

Drawing of the screen. Your own names and numbers will be different.

3See upper and lower jaw together (Bite View)

  1. Upload both an upper and a lower scan for the patient.
  2. Click Bite View at the top of the left list.
  3. Both jaws open together, each sitting on a study-model base.
  4. Rotate and zoom as usual.
  5. Scroll down to Model check to read the checks: if the base faces are parallel, the base thickness, the occlusal plane, and Watertight.

Tip: Green numbers in Model check are good. Yellow ones need a look.

Note: Bite View only shows when the patient has both an Upper Arch and a Lower Arch scan. The base is built by the software. If a scan edge is not usable you will see "A base could not be built for one of the arches". The numbers in Model check are worked out from the model on screen; they are a help for checking the model, not a clinical measurement.

Drawing of the screen. Your own names and numbers will be different.

4Adjust the bite by hand and save it

  1. Open Bite View.
  2. Scroll to the box Adjust the bite.
  3. Use the − and + buttons to move the lower jaw: L/R (left / right), F/B (front / back), U/D (up / down).
  4. Use Tilt, Turn and Roll to rotate the lower jaw a little.
  5. Watch the model until the teeth meet correctly.
  6. Click Save alignment. The word Saved shows.

Tip: Saved once, the bite stays the same next time you open this patient.

Note: Moving the bite by hand is done by eye. It is not a measured bite record.

Drawing of the screen. Your own names and numbers will be different.

5Change colours, background and lighting

  1. Click Appearance & export on the tool strip.
  2. Under Base colour, click As built, Classic Pink, Ivory, Blue Stone or Yellow Stone, or pick your own with Custom.
  3. Under Teeth, click As built, Warm white, Cool white or Plaster, or Custom.
  4. Choose the tooth finish: Matte (plaster), Natural or Wet look.
  5. Under Background, click Dark, Light, Grey, Black or Teal, or Custom.
  6. Under Lighting, click Standard, Clinical, Studio, Warm or Cool.

Tip: A Light background with Classic Pink base looks like a real plaster study model in a screenshot.

Note: Colours are only for the screen and screenshots. They are not saved into exported files.

Drawing of the screen. Your own names and numbers will be different.

6Cut through the model (Cross-section)

  1. Click Cross-section (the scissors) on the tool strip.
  2. A Cross-section box opens under the model.
  3. Click X, Y or Z to choose the direction of the cut.
  4. Drag the slider to move the cut through the model.
  5. Click Flip side to see the other half.
  6. Click Cross-section again to switch it off.

Note: This only hides part of the model on screen. The scan file itself is not changed.

Drawing of the screen. Your own names and numbers will be different.

7Save a picture, or put the view in the patient document

  1. Rotate the model to the view you want to keep.
  2. To save a picture on your computer, click Screenshot (the camera) on the tool strip. A PNG file downloads.
  3. To keep the view in the patient record, scroll to Send to patient document.
  4. Click Send to document.
  5. The button changes to Added to document for a few seconds.

Tip: To send a scan picture to a patient, save a Screenshot and send that picture yourself.

Note: Only a flat picture of the view is added to the patient document, not the 3D model. There is no patient share link for 3D scans.

Drawing of the screen. Your own names and numbers will be different.

8Export the 3D model for a lab

  1. Open the scan or the Bite View.
  2. Click Appearance & export on the tool strip.
  3. Scroll to Export 3D model.
  4. Click STL or OBJ.
  5. The file downloads to your computer. Send it to the lab.

Note: The file holds the model with its base, as it is positioned on screen. Colours and the cross-section are not part of the file. If nothing is showing you will see "Nothing is visible to export."

Drawing of the screen. Your own names and numbers will be different.

Did this not solve it? Message our support team and we will help you.