CBCT: viewer, implant sites and radiology report

What it is forOpen a CBCT from its DICOM folder or a ZIP, scroll the axial, coronal and sagittal slices, draw the arch for a panoramic and numbered cross-sections, trace the inferior alveolar canal, measure each implant site slice by slice (height from the crest to the vital structure, width at the crest and below), place virtual implants with clearance checks and write the radiology report with the sections each department asks for.
What you getA CBCT study on the patient with its measurements, a PDF report laid out like a radiology centre's (site tables by region, bone quality, findings, impression, pictures, signature) and, when you send it, a "CBCT Report" section in the patient document.
Where to find itLeft menu → CBCT
Who can use itOwner and staff with the Imaging permission

Good to know: Included from the Advanced plan and in college plans. Also sold on its own as the CBCT plan (1, 2 or 3–4 users; each login works on one device at a time), with its own login page (/cbct/login).

1Open the CBCT

  1. Open CBCT and choose the patient (or add a new one).
  2. Click Open DICOM folder and choose the folder from the scan centre's CD or USB — or ZIP or DICOM files for a ZIP or a single multi-frame file.
  3. The scan is read in your browser, put in order by slice position and saved to the patient, compressed. A bar shows the progress.
  4. If the name inside the scan is not the patient you chose, you are asked before it is added.

Note: Uncompressed, RLE, JPEG lossless and baseline JPEG DICOM open. A study saved as JPEG 2000 or JPEG-LS must be exported again from the scanner software as uncompressed DICOM — the screen says so when that is needed.

Drawing of the screen. Your own names and numbers will be different.

2Draw the arch: panoramic and cross-sections

  1. In Panoramic & cross-sections, scroll the axial (mouse wheel) to the level of the roots.
  2. Click Start the arch and click along the middle of the ridge from the patient's right to left — five or six points are enough. Drag a point to move it; Shift-click removes it. Click Done.
  3. The panoramic and the numbered cross-sections appear. Choose the section spacing (0.5, 1, 2 or 3 mm), the section width and slab.
  4. Click on the panoramic or the axial to go to a site, or use the arrow keys (Shift + arrow moves 5 sections). The big section is the one being measured; its number is the slice number of the report.

Tip: Ctrl + wheel zooms, the middle mouse button pans, a double-click fits the image again.

Drawing of the screen. Your own names and numbers will be different.

3Measure an implant site slice by slice

  1. Go to the cross-section through the site and click Measure a site on cross-section ….
  2. Click, in order: the top of the alveolar crest; the vital structure (upper border of the canal, or the sinus / nasal floor); the lingual and buccal edges at the crest; the lingual and buccal edges on the dashed line below the crest (1–5 mm, 3 mm by default).
  3. Check the values, type the tooth number (FDI), choose the density (Misch) if you wish and add a comment such as the mesiodistal width.
  4. Click Save site. The row goes into the report table under its region and the cross-section picture, with the lines and numbers, goes into the report pictures.

Note: The suggestion is the largest standard implant that keeps 2 mm from the canal (1 mm from the sinus floor) and 1.5 mm of bone on each side. These clearances can be changed in the Report tab. CBCT grey values are not Hounsfield units, so density is your choice.

Drawing of the screen. Your own names and numbers will be different.

4Trace the canal and plan the implant

  1. Click Canal R (or Canal L) and click the upper border of the canal on the cross-sections, moving a few sections each time. Clicks on the panoramic work too but lie on the arch curve.
  2. On a measured site, click Plan implant. The suggested size is placed on the crest; change the diameter, length, brand and tilt.
  3. Read the clearances: to the traced canal, to the marked vital structure, buccal and lingual bone, and to other implants. Anything closer than the rule turns red.
Drawing of the screen. Your own names and numbers will be different.

5Other measurements and the report

  1. In MPR, use the distance, angle and grey-value tools on any view — TMJ joint spaces on the sagittal, lesion size in three planes, root length, palatal bone.
  2. Use the camera button on any image to add it to the report.
  3. In Report, fill the details, turn on the sections asked for (implant, impacted teeth, lesion, endodontic, periodontal, orthodontic, TMJ, bony changes) and enter the findings. TMJ spaces are compared with Ikeda & Kawamura (2009) and the condyle position is worked out with the Pullinger & Hollender ratio.
  4. Write the other findings and the radiological impression (one point per line), the name and qualification of the reporting doctor, and check the notes.
  5. Click PDF report, or Send to document to add it to the patient document.
Drawing of the screen. Your own names and numbers will be different.

Did this not solve it? Message our support team and we will help you.