Good to know: Needs the 3D model viewer in your plan (Advanced and above). Also sold on its own as the Study Model Analysis plan (1, 2 or 3–4 users; each login works on one device at a time), with its own login page (/study-model-analysis/login).
Lessons on this page
1Start an analysis
- Open 3D Scans and choose the patient. Upload the scan if it is not there yet.
- Scroll below the viewer to Study model analysis.
- Click Permanent dentition or Mixed dentition.
- Everything saves by itself; "Saved" at the top right confirms it.
Tip: Scanner files are in millimetres. If a scan is clearly not, a warning appears — then type caliper values instead.
3D Scans
2Patients and the patient document (Study Model Analysis plan)
- Click Patients in the left menu.
- Click Add patient, fill in the name (mobile, email, gender, date of birth and address are optional) and click Save patient.
- Click the patient, then Open 3D scans & study model to work on them.
- In the study model analysis, click Send to document. The report is saved in that patient's document.
- Back in Patients, click the patient: every report you sent is listed. Click Report for one report, or Download patient document (PDF) for all of them with a cover page of the patient's details.
Tip: The patient document holds only the reports you sent with Send to document. Click the × next to a report to take it out of the document — the analysis itself is kept.
Patients
3Measure the teeth on the scan
- Open the Upper scan (or Bite View) and go to the Tooth widths tab.
- Click Measure upper teeth on the scan. The bar on the viewer shows which tooth is next, starting with 16.
- Click one contact point of the tooth, then the other (the widest mesiodistal points). The width appears in the chart and the next tooth starts by itself.
- Dragging still rotates the model; a click places a point. Undo point or Backspace removes the last one, Escape stops.
- The tool bar on the viewer has Undo (also Ctrl+Z — takes back the last measurement, typed value or erase), the Eraser (click a point or line to remove it with its value) Draw (drag on the model to draw in a colour; hold Shift for a straight line) and Straight line (press where the line starts, drag to the end and release — its length shows while you drag). Drawings appear in the report picture.
- Do the same for the lower teeth on the Lower scan. You can also type any width, or click the crosshair under one tooth to measure only that tooth again.
Note: For a rotated, malformed or carious tooth, the ⇄ button copies the width of the same tooth on the other side.
Study model analysis
| 16 | 15 | 14 | 13 | 12 | 11 |
|---|---|---|---|---|---|
| 10.3 | 6.8 | 7.1 | 7.9 | 6.7 | 8.7 |
4Arch measurements
- Go to the Arch measurements tab. Each line says exactly where the points go.
- Arch perimeter: click from the mesial of the first molar along the contact points, premolar cusps and incisal edges to the mesial of the opposite first molar, then Finish (segmental method).
- Pont premolar and molar widths, Korkhaus anterior length, Howe PMBAW, PMD and BAL, and the intercanine and intermolar widths work the same way — the bar on the viewer names each point in turn.
- BAL: two points — A point on the cast, then the midline point on the line joining the distal surfaces of 16 and 26. For BAL and PMBAW the points may go on the gum, palate or model base.
- All widths, arch widths and the arch perimeter are measured parallel to the occlusal plane, as a caliper or brass wire would, so a click slightly higher or lower on a tooth does not change the value. A width outside the usual range for that tooth is shown in yellow — usually a buccal/lingual click instead of the two contact points. Recalculate from points re-works older analyses the same way.
- Little's irregularity index: in the Little block click, for each of the five lower anterior contacts (43/42 to 32/33), the contact point of one tooth and then of the next — the displacement is measured parallel to the occlusal plane. Type 0 where the contacts touch.
- Peck & Peck: in the Tooth widths tab enter (or measure on the scan) the labiolingual width of 42, 41, 31 and 32; the MD ÷ FL index and any reproximation needed are worked out.
- Lundström segments: click Mark 7 points on scan (distal of 6, contacts 5/4, 3/2, the midline, 2/3, 4/5, distal of the other 6) — the six segment lengths fill in. Or type each segment measured with dividers.
- A typed arch perimeter is taken as a brass-wire measurement; the report says which method was used.
- Use Add measurement for anything else, for example overjet in Bite View (one point on each arch).
Arch measurements
5Mixed dentition: Huckaba
- The scan cannot tell a primary tooth from a permanent one, so in the Tooth widths tab mark every position P (permanent), D (primary) or – (missing / unerupted). The width box then belongs to that tooth (13 or 53).
- Erupted permanent canines and premolars are used as measured; for the others the predicted width (Moyers / Tanaka & Johnston) or the X-ray width (Huckaba) is used. Moyers and Tanaka & Johnston need all four lower incisors marked permanent.
- In the X-ray (Huckaba) tab, type the width of each unerupted tooth and its primary tooth as seen on the periapical X-ray.
- The actual width is worked out as X-ray width × primary width on the cast ÷ primary width on the X-ray, and Nance uses it.
X-ray (Huckaba)
| Unerupted tooth | On X-ray | Primary on cast | Primary on X-ray | Actual |
|---|---|---|---|---|
| 43 (83) | 8.0 | 6.0 | 6.4 | 7.5 mm |
6Read the results and send to the document
- Open the Results tab: every analysis shows its formula, the result and the guideline from the notes (for example Carey: −2.5 to −5 mm → extraction of second premolars).
- Lines that cannot be worked out yet say which tooth or measurement is missing.
- Under Analyses in the report, choose the pictures (3D model as on screen, upper and lower occlusal views) and tick the analyses to print (All / None).
- Rotate the 3D model the way you want it pictured, then click Send to document. Use Download PDF report for a separate report. The report gets a high-resolution picture of that view plus the occlusal view of each arch, the key findings in coloured cards, and every line of each analysis with its formula and method.
Note: Cut-offs differ slightly between textbooks, and the decision also depends on profile, overjet, lip protrusion, curve of Spee, growth and the patient.
Results
| Analysis | Result |
|---|---|
| Bolton overall | 91.56 % |
| Carey | −2.9 mm |
| PMBAW % | 41.7 % |
Did this not solve it? Message our support team and we will help you.
