Lessons on this page
1Understand what you need before you start
- Open Imaging (RVG) and click the Devices tab.
- Read the box How sensor capture works.
- Check that you have a Windows computer with the X-ray sensor plugged in, and that the sensor already works in its own program.
- Check that you have the bridge files. They are in the bridge folder of the software package, with a guide file named README-BRIDGE.md.
- Decide the mode. Folder watch: the sensor program saves each image into a folder and the bridge picks it up. TWAIN driver or WIA driver: the bridge asks the sensor driver for the image through the free NAPS2 tool.
Tip: Start with Folder watch. It only needs the sensor program to save each image as a file in one folder.
Note: We do not promise that every sensor brand works. It depends on your sensor, its own software or driver, and the bridge program. Direct control of a brand SDK is not included. Test your sensor model in your clinic before you rely on it. Until it works, use Import files.
Imaging (RVG)
2Add the capture PC
- On the Devices tab, click Add capture PC.
- Type a name in PC name, for example "Chair 2 PC".
- Type the room or chair in Room / chair.
- Choose the Mode: Folder watch, TWAIN driver or WIA driver.
- Click Add & get pairing code.
- A dark box shows a Pairing code. Keep this screen open for the next task.
Note: The pairing code is valid for 30 minutes only.
Imaging (RVG)
Devices
3Pair the bridge on the sensor computer
- Go to the Windows computer that the sensor is plugged into.
- Open the bridge folder there.
- On the Devices tab, click the copy button beside the command shown in the dark box.
- On the sensor computer, run that command inside the bridge folder, as the box tells you.
- Then double-click start-bridge.bat.
- Go back to the Devices tab. In a few seconds the card shows Paired and Online.
Tip: If the code ran out, click New pairing code on the card and try again.
Note: The bridge must stay running on that computer. If the computer is off or the bridge is closed, the card shows Offline and Capture will not work.
Imaging (RVG)
“Chair 2 PC” added — pair the bridge now
4Set the watched folder or the sensor driver
- On the device card, click Settings.
- Check Name, Room / chair and Capture mode.
- For Folder watch: type the folder path in Folder on the capture PC where the sensor software saves images, for example C:\EzDent\Export. It must be the same folder your sensor program saves into.
- For TWAIN driver or WIA driver: choose your sensor in Sensor driver. If the list says "Start the bridge to list drivers", start the bridge first.
- If you know it, type the Sensor pixel size (µm) from the sensor spec sheet. This lets new images be measured in mm without calibrating each one.
- Tick Also send images taken without pressing Capture (they go to the Inbox) if you want those images kept too.
- Click Save.
Tip: If you do not know the pixel size, leave it empty. The card will say "no sensor pixel size (measurements in px until calibrated)".
Note: A wrong pixel size gives wrong mm values on every image from that sensor. Only type it if you are sure, and check one image against an object of known length.
Imaging (RVG)
Devices · Chair 2 PC
5Test the connection
- Make sure the bridge is running on the sensor computer.
- On the device card, click Test connection.
- Wait a few seconds.
- Read the result. Connection test passed means all is fine.
- Connection test found problems shows a list. A red cross marks the step that failed, with a short reason.
- Fix that step (for example the folder path) and click Test connection again.
Tip: Messages on the card help too: "The bridge cannot open the watch folder." means the folder path is wrong. "2 image(s) waiting on the PC to upload." means images are safe on that computer and will come when the internet is back.
Note: Test connection only works after the computer is paired.
Imaging (RVG)
Devices
6Re-pair or remove a capture PC
- Open the Devices tab.
- To connect the bridge again (for example after Windows was reinstalled), click Re-pair on the card.
- Click OK on the warning. A new pairing code shows. Pair the bridge again as before.
- To take a computer off the list, click Remove.
- Click OK to confirm.
Note: Re-pair disconnects the bridge until it is paired again. Remove stops the bridge on that computer from working. X-rays already taken are kept.
Imaging (RVG)
Devices
Did this not solve it? Message our support team and we will help you.
