What it is forTake one X-ray, or a full set (a series), for one patient. The software asks the sensor computer for the next image and puts it on this patient only.
What you getEach new X-ray lands on the patient chart with the tooth number and the type already filled in.
Where to find itLeft menu → Imaging (RVG) → Capture
Who can use itOwner and staff with the Imaging (RVG) permission

1Take a single X-ray

  1. Open Imaging (RVG) and click the Capture tab.
  2. Choose the patient in the search box. You must choose the patient first.
  3. Under What are you taking?, click Single image.
  4. Under Tooth (optional for a single image), click the tooth number.
  5. Choose the Image type, for example Periapical (IOPA).
  6. Check the computer name beside the small screen icon. It should say Online.
  7. Click Start Single image, then click Capture.
  8. When the screen says "Sensor ready — position the sensor and expose now.", take the X-ray. The picture shows in a few seconds.

Tip: Click the new picture to open it in the viewer.

Note: Capture needs a paired computer that is Online (see Devices). If you see "Add and pair an imaging PC first (Imaging → Devices)." do that first, or use Import file(s) instead. If no image comes in time you will see "Nothing arrived from the sensor in time." — click Capture again.

Drawing of the screen. Your own names and numbers will be different.

2Take a full series (FMX, bitewing, endo and others)

  1. On the Capture tab, choose the patient.
  2. Under What are you taking?, click the series: Full mouth series (FMX) — adult, Bitewing series, Endodontic series, Periodontal series, Implant follow-up, Orthodontic records or Pediatric series.
  3. If a tooth chart shows (endo and implant), click the tooth. It is needed for these series.
  4. Click the Start button.
  5. The left side lists every image of the series. The big box shows the one to take now.
  6. Click Capture, then take the X-ray.
  7. With Auto-continue to the next image ticked, the software gets ready for the next image by itself. Keep taking X-rays until the list is done.
  8. When you see Series complete, click Close.

Tip: Click any line in the left list to jump to that image. A green tick means taken.

Note: If a picture looks too dark or too light, a yellow line says "consider a retake". This is a simple exposure check, not a diagnosis.

Drawing of the screen. Your own names and numbers will be different.

3Retake, skip or import one image of a series

  1. In the series, click the image in the left list.
  2. To take it again, click Retake. The older try is kept in the patient timeline.
  3. To leave it out, click Skip and type the reason (for example "tooth missing"). Then click OK.
  4. If you skipped by mistake, click the image and then Take it anyway.
  5. If you already have the picture as a file, click Import file for this slot and choose the file.
  6. To stop a capture that is waiting, click Cancel capture.

Note: A reason is required to skip. If you leave it empty, nothing is skipped.

Drawing of the screen. Your own names and numbers will be different.

4Pause a series and finish it later

  1. While a series is open, click Pause. Or just click Close.
  2. Later, open the Capture tab and choose the same patient.
  3. Look at the box Unfinished series for the patient.
  4. Click the series button, for example "Endodontic series · 2/4".
  5. If it was paused, click Continue.
  6. Take the images that are left.

Tip: On the Patients & images tab the series also shows with a badge In progress or Paused. Click Continue there.

Note: While a series is paused, the Capture button is switched off. Click Continue first.

Drawing of the screen. Your own names and numbers will be different.

5Save a series as your own template

  1. Open or finish a series on the Capture tab.
  2. Click Save as template.
  3. Type a name for the template and click OK.
  4. A message says "Saved. It will appear in the template list."
  5. Next time, find it under What are you taking?.

Tip: You can also build templates by hand in the Settings tab under Acquisition templates.

Drawing of the screen. Your own names and numbers will be different.

6When the sensor is busy with another patient

  1. If someone else already pressed Capture on the same computer, you see a red message that the sensor is busy.
  2. Wait for the other person to finish, then click Capture again.
  3. If the other request is stuck, a person with the Approvals permission (or the owner) sees a link Take over the sensor.
  4. Click Take over the sensor to cancel the other request and start yours.

Tip: If two sensor computers are added, choose the right one in the list beside the small screen icon before you click Capture.

Note: Only one patient can use one sensor at a time. This stops an X-ray going to the wrong chart.

Drawing of the screen. Your own names and numbers will be different.

Did this not solve it? Message our support team and we will help you.