What it is forThe viewer opens one X-ray large. You can make it brighter, zoom, turn it, draw on it, measure and write notes.
What you getYour changes are saved by themselves as separate layers. The original X-ray file is never changed, and you can always go back.
Where to find itLeft menu → Imaging (RVG) → click any X-ray
Who can use itOwner and staff with the Imaging (RVG) permission

1Open an X-ray and move between images

  1. Click any X-ray picture in Imaging (RVG) or on the patient profile.
  2. The viewer opens. The top line shows the patient name, tooth, type, date and where the image came from.
  3. Click the > arrow (Next image) or the < arrow (Previous image) to move through the images. The arrow keys on the keyboard work too.
  4. Watch the small text All changes saved at the top. It turns to Saving… while it saves.
  5. If it says Not saved, click Retry.
  6. Click the X at the top left to close the viewer.

Tip: On a small screen, click the sliders icon (Tools & notes panel) to open the right side panel.

Drawing of the screen. Your own names and numbers will be different.

2Change brightness, contrast and other picture settings

  1. In the viewer, click the Adjust tab on the right.
  2. For a quick look, click a button under Presets: Original, Endo, Caries, Bone / perio, Smooth or Negative.
  3. Or drag the sliders: Brightness, Contrast, Gamma, Sharpen and Smooth.
  4. Tick Negative to invert the picture (white becomes black).
  5. Tick Auto-level to spread out the grey tones, Reduce noise to clean grain, or Grayscale to remove colour.
  6. To undo all of it, click Reset adjustments.

Tip: Keyboard: press I to switch Negative on and off.

Note: These settings only change how the picture looks on screen. The stored original is not touched.

Drawing of the screen. Your own names and numbers will be different.

3Zoom, move, rotate and flip

  1. Use the bar above the picture.
  2. Click Zoom in or Zoom out. You can also scroll the mouse wheel, or pinch with two fingers on a touch screen.
  3. Click Fit to screen to see the whole picture. Click 1:1 to see actual pixels.
  4. To move the picture, choose the hand tool (Pan) on the left and drag.
  5. Click Rotate left or Rotate right to turn the picture by a quarter turn.
  6. Click Flip horizontal or Flip vertical to mirror it.

Tip: Keyboard: + and - zoom, 0 fits to screen, H picks the Pan tool.

Note: Flipping changes left and right on screen. Check the tooth number before you write a finding.

Drawing of the screen. Your own names and numbers will be different.

4Use the viewing helpers (marks, original, split, magnifier, spotlight, grid)

  1. Click the eye button (Show / hide marks) to hide or show all drawings.
  2. Click Show unprocessed original to see the picture with no adjustments.
  3. Click Before / after split and drag the divider line. One side shows the original, the other side your adjusted picture.
  4. Click Magnifier and move the mouse to enlarge a small area.
  5. Click Spotlight and move the mouse to light up one area and dim the rest.
  6. Click Grid to lay a grid over the picture.
  7. Click a button again to switch it off.

Note: The grid squares are 5 mm only when the image is calibrated. If it is not calibrated, the grid is 50 pixels and does not show real size.

Drawing of the screen. Your own names and numbers will be different.

5Draw and mark on the X-ray

  1. Pick a tool from the Mark group on the dark strip at the left: Arrow, Line, Rectangle, Circle / ellipse, Freehand, Highlighter, Region outline, Text label, Tooth number, Numbered marker or Stamp.
  2. Pick a colour dot and a line width (1px to 8px) in the bar above the picture.
  3. For Arrow, Line, Rectangle and Circle / ellipse: press, drag and let go.
  4. For Freehand and Highlighter: press and draw like a pen.
  5. For Region outline: click point after point around the area, then double-click (or press Enter) to finish.
  6. For Text label: click a spot and type the text. For Tooth number: click a spot and type an FDI number such as 36.
  7. For Numbered marker: each click adds 1, 2, 3… For Stamp: choose the wording in the bar (Recheck, Caries?, Periapical lesion?, Missing, Retake, Review with faculty), then click a spot.

Tip: Press Esc to cancel a drawing you have started. Keyboard: T = Text label, F = Freehand.

Note: A stamp such as Caries? is only a note written by the user. The software does not find disease by itself.

Drawing of the screen. Your own names and numbers will be different.

6Move, delete, undo and redo a mark

  1. Choose the arrow-pointer tool (Select / move / delete) on the left strip.
  2. Click a mark to select it.
  3. Drag it to move it.
  4. To remove it, click the bin button (Delete selected mark) at the bottom of the strip, or press the Delete key.
  5. Click Undo to take back the last change. Click Redo to bring it back.

Tip: Keyboard: Ctrl+Z = Undo, Ctrl+Y = Redo, V = Select tool.

Drawing of the screen. Your own names and numbers will be different.

7Show the X-ray to the patient (Consultation mode)

  1. In the viewer, click the screen button named Consultation mode — full screen for the patient.
  2. The X-ray fills the whole screen on a black background.
  3. Use the arrow button (Point with an arrow) and drag to point at something.
  4. Use Spotlight to light up one area, Show marks to hide or show drawings, and Fit to see the whole picture.
  5. Use the < and > buttons to move to another image.
  6. Click the Exit button (or press Esc) to go back.

Tip: If you wrote a Radiographic finding or a Recommendation / plan, they show at the bottom as "Finding" and "Plan" in large text for the patient.

Drawing of the screen. Your own names and numbers will be different.

Did this not solve it? Message our support team and we will help you.